/5 oil flow issue

Sat Jun 19 10:10:52 EDT 2021

Take Two: https://youtu.be/0OiJpaVJyH0

No Joy.

Note: I forgot to remove (and ground) the spark plugs this time but I had
the green coil wire off. The battery was strong enough for the test anyway.

It's on YouTube this time so feel free to comment there if you like.

On Fri, Jun 18, 2021 at 4:42 PM Tom Cutter <rubberchickenracing at gmail.com>
wrote:

> oops, I made a typo! SHOULD SAY " If no joy, you know the pump is NOT
> working"
>
> --
> Tom Cutter
> Yardley, PA
> www.RubberChickenRacingGarage.com
>
> "Normalize telling your friends that you love them. Tell them a lot. Make
> it weird." --unk
>
>
>
>
>
> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=icon> Virus-free.
> www.avast.com
> <https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail&utm_term=link>
> <#m_3493305825176858612_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>
> On Fri, Jun 18, 2021 at 4:00 PM Tom Cutter <rubberchickenracing at gmail.com>
> wrote:
>
>> I’d put it on the centerstand with a 1/2” shim under the right hand leg
>> of the stand. Hold a pan under the filter cavity, because this test gets
>> messy if everything is working. If no joy, you know the pump is t working,
>> probably because the tiny key slipped out. I glue the key in with Elmer’s
>> glue so it doesn’t fall. The glue dissolves in the hot oil and is harmless.
>>
>> Tom Cutter
>> Rubber Chicken Racing Garage
>> Yardley, PA USA
>> RubberChickenRacingGarage.com
>>
>> On Jun 18, 2021, at 3:19 PM, Craig Barnhart <barney12231963 at gmail.com>
>> wrote:
>>
>> 
>> I just got some feedback.
>>
>> Someone said I leaned the bike over too much for the pickup to get oil to
>> the pump.
>>
>> If so, should I just put the bike on the side stand and do it again?
>>
>> On Fri, Jun 18, 2021 at 2:52 PM Craig Barnhart <barney12231963 at gmail.com>
>> wrote:
>>
>>> Looks like I'll be disassembling from the rear to get to the oil pump.
>>>
>>> https://photos.app.goo.gl/STcPCtZkrEEWXM9G6
>>>
>>> You can ignore my unedited speech bloopers at the end.
>>>
>>> Craig
>>>
>>> On Wed, Jun 16, 2021 at 12:39 PM Craig Barnhart <
>>> barney12231963 at gmail.com> wrote:
>>>
>>>> Thank you sir!
>>>>
>>>> That's exactly what I wanted, a direction to go.
>>>>
>>>> Maybe I'll take a video to determine what "A LOT" means.
>>>>
>>>> On Wed, Jun 16, 2021 at 11:45 AM Tom Cutter <
>>>> rubberchickenracing at gmail.com> wrote:
>>>>
>>>>> Craig-
>>>>>
>>>>> I use a system called Divide and Conquer. In this case this means look
>>>>> at the system in parts. To do this first remove the oil filter cover (bike
>>>>> laid partly over to left) and see if it is full of oil. A tap on the
>>>>> starter (plugs out/grounded) will tell you if the oil pump is working. If
>>>>> you don't get a LOT of oil coming out of the pump cavity very fast, (this
>>>>> will be messy) then the pump is the problem. On a /5 that means the
>>>>> woodruff key slipped, so you know where you have to go to fix that. VERY
>>>>> common fault with the /5 which uses that tiny key.
>>>>>
>>>>> Check that, report back.
>>>>>
>>>>> --
>>>>> Tom Cutter
>>>>> Yardley, PA
>>>>> www.RubberChickenRacingGarage.com
>>>>>
>>>>> "Normalize telling your friends that you love them. Tell them a lot.
>>>>> Make it weird." --unk
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> On Wed, Jun 16, 2021 at 11:35 AM Craig Barnhart <
>>>>> barney12231963 at gmail.com> wrote:
>>>>>
>>>>>> Greetings Airheads,
>>>>>>
>>>>>> I have an oil flow issue on my newly assembled 1972 R50/5 project
>>>>>> bike, and I'm scratching my head trying to determine the next steps.
>>>>>>
>>>>>> This is the first time I ever attempted to start the bike, and I am
>>>>>> not getting oil from the sump to the cylinder heads, and only a residual
>>>>>> amount to the oil sensor (oil pressure light stays on).
>>>>>>
>>>>>> *Background:*
>>>>>>
>>>>>> As part of this three-year (part time) project, I replaced all seals
>>>>>> including the fuel pump's o-ring and cover, the woodruff key, and visually
>>>>>> inspected (no measurements) the fuel pump. I also replaced the pickup
>>>>>> gasket.
>>>>>>
>>>>>> *What I've done since the issue, not necessarily in this order:*
>>>>>>
>>>>>>    1. Read thru this thread:
>>>>>>    https://advrider.com/f/threads/airhead-oil-priming-problem-ha.746898/.
>>>>>>    The *Bill Harris, Dec 5, 2011 *entry is the best summary on the
>>>>>>    page.
>>>>>>    2. Studied Snowbum's diagram and notes:
>>>>>>    https://bmwmotorcycletech.info/oilsketch.htm
>>>>>>    3. Tested the oil sensor switch.
>>>>>>    4. Filled the oil filter cavity with oil to prime it (laid the
>>>>>>    bike on its side to fill--learned this trick from Tom Cutter).
>>>>>>    5. Hand pumped (as best I could) oil into the oil sensor hole to
>>>>>>    prime it.
>>>>>>    6. Visually checked the pickup, bolts, and gasket
>>>>>>    7. Blew air (with an air compressor) into the pickup and felt air
>>>>>>    coming out of the right cylinder.
>>>>>>    8. Blew air into the oil sensor hole.
>>>>>>    9. Blew air into oil filter cavity holes.
>>>>>>
>>>>>> *Outcomes after turning over the engine (spark plugs out; green coil
>>>>>> wire off) for 90 seconds at a time:*
>>>>>>
>>>>>>    1. I got a tiny bit of oil into the left head (right side of the
>>>>>>    left head) at one point of the process.
>>>>>>    2. Oil is coming into the oil filter cavity.
>>>>>>    3. There is residual oil in the oil sensor hole (seeps out when
>>>>>>    sensor is removed), but it doesn't flow out when turning over.
>>>>>>
>>>>>> *AFAIK this is what is left to check:*
>>>>>>
>>>>>>    1. Oil pump - Visually inspect again and take measurements this
>>>>>>    time (remove flywheel, etc.)
>>>>>>    2. Oil pressure relief valve - Make sure it's not stuck open
>>>>>>    (remove timing cover)
>>>>>>    3. Ensure front main bearing cap oil passage hole lines up with
>>>>>>    engine block hole - Not sure if I can do this visually without removing the
>>>>>>    main bearing or cap  (remove timing cover)
>>>>>>    4. Something clogged in the system - I don't know how to check
>>>>>>    this other than blowing air through it.
>>>>>>
>>>>>> *Questions:*
>>>>>>
>>>>>>    1. Can I narrow it down to one area before disassembling the rear
>>>>>>    and/or front end?
>>>>>>    2. Is there any way to test the system after disassembling
>>>>>>    besides a visual inspection and measurements?
>>>>>>    3. I can tow the bike to Chris' tech day if anyone thinks it
>>>>>>    would help to see it in person. Does anyone think it would be helpful to
>>>>>>    bring it?
>>>>>>
>>>>>> Thank you!
>>>>>> Craig
>>>>>>
>>>>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.dudley.nu/pipermail/mdairheads/attachments/20210619/b70c8af0/attachment.htm>